The Sewing Machine Confuses the Threads from Below: Causes and Solutions

The Sewing Machine Confuses the Threads from Below: Causes and Solutions

Both experienced seamstresses and beginners have a problem with productivity at times which causes the sewing machine to knot threads in the bottom. It is also common for needles to get caught in the resulting combination of finely twisting yarns. It’s impossible to work with an embroidery machine when it is in this condition. To comprehend the causes and the causes of the issue You should be familiar with them more deeply.

Why Does the Machine Get Caught in the Thread of the Bobbin?

Most of the time, this happens because of certain events.

  • The wrong threads. Most of the time, it’s the thread on the bottom that is not threaded correctly by women who are craftspeople, particularly beginners. When sewing it is important to thoroughly examine;
  • A needle that is not correctly selected. Both the threads and needle must be chosen in accordance with the specifications of the fabric being used. Work should be started only when the diameter of the blade is equal to the material’s density otherwise a tangle may develop on the reverse;
  • Installing a non-pointed, bent needle. Notches on the needle’s tip cause a tangle at the top of the material. Only the best even devices must be used to sew (you can test the evenness of the needle by using an eye-to-eye mirror or simply by looking);
  • Insufficient coordination of tension of the lower and the upper threads;
  • The problem is installing the friction washer onto the flywheel
  • An incorrectly placed needle. The amount is often weaker and the most critical device is below the recommended threshold. When fitting an element that is suitable for the model of sewing machine that is already in use it is crucial to be aware of the large groove of the piece;
  • The sudden action of the gear rack;
  • The incorrect Bobbin is not right. It is recommended to purchase and use only the spool that is suited to the requirements of the method. Setting a different setting makes the machine manual to unravel the thread from the bobbin. The differences between the bobbins by 0.5-1.0 millimeters will impact the effectiveness of the machine;
  • The excessively frequent pressing of the material with hand. Because of these manipulations, threads can be damaged or tangled, and cause the damage to the material is more frequent;
  • The thread on the bottom is denser than the thread on top. Since the primary focus is on the top thread (it pulls the thread from in the bottom plan) It is important to select threads that are thicker than the bottom one or are the same in strengths and density indicators.
  • An incorrectly calibrated rail that is not calibrated correctly. The issue mentioned above will occur when incorrect settings are set on the tooth area.

How Do You Thread Correctly?

If the sewing machine misinterprets the thread at the bottom, in order to correct this issue, place the bobbin inside the correct cap and then slide the thread into a specific hole inside the cap that is under the spring plate. Then, put the cap back into the hook, and then pull out the lower portion through the needle connector on the upper portion. The last step is threading the foot under the cap.

Since the machine is unable to distinguish the thread on top it is required to perform the adjustment or full threading. It is important to place the yarn that is twisted into the machine’s body, then stretch it until it resembles the design that the regulator uses, and draw it through the spring for compensation. Then, it is crucial to slowly place the thread in the guide, then return it to an eye on the needle before attaching. It is imperative to remember that when performing this operation using a manual machine it is important to pay particular attention to selecting the needle and thread number for an item of a specific kind and density.

How Do You Adjust the Tension on the Threads on the Lower and Upper Threads

If the thread of the bobbin is caught in the machine then the bobbin thread correction process needs to be completed. To accomplish this, you need to hold the bobbin case that holds the bobbin in your palms and then slowly pull the thread’s ends to make it emerge somewhat snug. If you are concerned it is coming off too much, you should try to tighten the screw within the bobbin’s case. To be able to determine the tension level it is recommended to stitch several seams onto an unneeded piece of material.

After you have completed your adjustment for the lower thread it is time to remove the thread on the top. There’s a regulator either on the side of the machine or on the top. The progressive scrolling function of this device lets users make needed adjustments. It is important to constantly review the results of your efforts (flash the fabric and observe the quality of sewing) Repeat the process until you get a pleasing image achieved.

What Are the Other Possible Reasons That Could Cause the Machine to Misinterpret the Thread of the Bobbin?

If you observe that the machine is unable to distinguish the threads, and none of the reasons above is pertinent, it could be due to a lack of presser pressure applied by the foot to the material. If the fabric you choose to work with is extremely heavy it is essential to adjust the pressure manually in accordance with the current circumstance. The reason could be using threads that are not twisting correctly. On the market, you can discover not just left-handed but, right-handed. It is crucial to keep in mind that for sewing machines the majority of left-handed models are utilized.

If you do not have an advanced machine, but rather a traditional one that has outdated mechanics, you should pay attention to the maintenance of the machine. In the event that the machine is able to confuse the upper thread from below, and in many cases causes damage, it is essential to not just follow the steps above as well as oil the components. Because the surfaces of components get scratchy, the work becomes challenging, which adversely affects the performance of the entire mechanism. This is not just a problem for older machines, but also for new ones as regular cleaning and lubrication may prolong the life of the machine.

The tension of the thread should be checked and adjusted for every type of fabric. It is normal that cotton fabrics can’t be processed without an additional adjustment to the machine after sewing on silk. It is not advised to handle satin or thin fabrics if you’re the owner of handheld devices. The computer and electromechanical sewing machines can handle thin and sensitive fabrics more easily than conventional models.

What Should You Do If You Don’t Get Any Help?

If you’ve tried every procedure to fix the device’s performance If you are unable to attempt to fix the issue on your own. It is more beneficial to trust the device to experts. There are instances that the device can confuse the threads because of:

  • Problems with the pusher. The complete replacement of this component is needed;
  • broken compensation spring. A new spring is installed over the old one, and the tension force is adjusted.
  • defective tension stabilizer spring. Repair or replacement is the solution to the issue.
  • The paw’s notch is. The technician will try to smooth the element but if improvement does not occur, a total replacement is required.
  • issues with the structure of the bobbin case consequence of which the repair is or replaces done.

However, an experienced technician will evaluate the present situation and take all measures to restore the machine to its previous efficiency. Older models are more intricate designs, whereas the latest models (Janome, Brother, Pfaff, and so on.) are relatively basic in terms of technical characteristics. The latest models can stitch around 200 stitches inside a minute, are silent with minimal input from the user, and can make both decorative and regular stitches. A lot depends on the model and the capabilities it has. In spite of the condition of the device, devices can cause threads to be confused and the user of a helpful device should know the root causes of this situation as well as steps to restore the performance of the particular model.

Recent Posts