How to Adjust the Tension on a Brother Cs6000i Sewing Machine

How to Adjust the Tension on a Brother Cs6000i Sewing Machine

One of the most common complaints about sewing machines is that they are difficult to operate. However, Brother makes the CS6000I sewing machine so that it is easy to set up and use. The tension adjustment dial located on the top of the machine controls the tension of the thread as it is fed through the sewing machine. The tension dial can be adjusted at any time while the fabric is being sewn. Adjusting the tension carefully is important because too much tension will cause breakage in the needles or in rare cases, may damage your sewing machine.

The only way to adjust this setting is by using a screwdriver to turn a small screw underneath the dial face. Once you have turned the screw, test your stitch by pulling on it while still under tension. If your stitches are fraying, then you need to tighten your tension setting. If your stitches are tight and bunched up, then you need to loosen your tension setting.

This adjustment should be done a bit at a time, testing your stitch after each adjustment until you get it just right. Also make sure to check every other setting on your sewing machine when making this adjustment, since a change in one setting can cause changes in other settings as well.

The tension on the Brother CS6000I sewing machine can be adjusted in two ways: by adjusting the screw underneath the tension dial and by adjusting the dial itself.

Instructions

•Insert a piece of scrap of the same type into the machine as you sew. This will ensure that you will not be sewing on top of your moving stitch, but instead that your stitch goes underneath it.

•Make a few stitches to see how the tension needs to be adjusted. If you notice that there is too much extra fabric on one side, adjust the tension so that it becomes tight enough to the point where it makes an edge on the fabric.

•Turn the tension dial to a lower number to reduce the tension if slack appears on the surface of the fabric. This indicates that the tension is too tight.

•Turn the dial tension to a higher number if baggy appears on the wrong side of the fabric. This indicates that the tension is too loose.

•Continue adjusting until tension is correct, indicated by strong seams that do not pucker or bind excessively. Remove the scrap fabric and sew the piece that needs to be sewn.

What Should My Tension Be Set at on My Brother Sewing Machine?

The Brother CS6000i is the most advanced computerized sewing machine on the market, but there are still some crucial steps in the setup process that can be a bit confusing. One of the most important settings to make when using a new sewing machine is your tension setting. The tension setting determines how tightly or loosely your fabric will be pulled between your feed dogs and your needle. And if you’re anything like me, you’ve probably spent hours flipping through the manual, trying to determine what each of those numbers means and how they might affect the finished product. The good news? You don’t have to assume! Here’s a simple guide to help you determine what tension setting is right for you:

First, check how your current thread and fabric look. Are they puckered or rippling? If so, your tension is too loose. If they look nice and smooth, but they’re not staying straight on the fabric (instead they’re following along with the feed dogs), then your tension is too tight. Once you’ve determined whether your tension is too loose or too tight, adjust the dial:

 It’s best to set your tension at 4.0 on a Brother sewing machine. Let the upper thread and bobbin thread cross in the center of the fabric; only the upper thread should be visible from the right side and only the bobbin thread should be visible from the wrong side.

accordingly, until the stitch looks nice and even on both sides of the fabric. After that, try testing it out on some scrap material so that you can see whether it needs to

Does Brother Cs6000i Have Automatic Tension?

Brother CS6000i does come with automatic tension, but it includes a bobbin-case tension screw and instructions for adjusting the bobbin case tension. To adjust the bobbin case tension, you will need a small slotted screwdriver. First, loosen the (-) slotted head screw with your screwdriver. Then, turn the (-) screw clockwise to increase bobbin case tension. When you are finished with this adjustment, tighten the head screw back up with your screwdriver so that it is snug against the casing.

How Do I Know If My Sewing Machine Has Tension?

 To find out if your sewing machine has the right tension, hold a bobbin by the thread and see if it moves. If the bobbin drops down when you tug on the thread, then the tension is just right. If it doesn’t move at all, then your machine has too much tension.

Recent Posts